Moogumi Futaba 10CG 2. Note that you have to turn ffutaba transmitter off and back on before a modulation change becomes effective. Find and correct the problem. Your 10CG contains four separate linear programmable mixes.
|Published (Last):||8 June 2008|
|PDF File Size:||4.90 Mb|
|ePub File Size:||20.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 3: Website: www. Internet location of extensive technical information Futaba products. This product may be used for model airplane or surface boat, car, robot use. It is not intended Page reversed polarity during charging. Page Stick adjustments: change stick tension and height. Adjusting the length of the non-slip control sticks You may change the length of the control sticks to make your In order to start Page Voltmeter, voltage reading: displays transmitter voltage on home screen.
Since these functions are The name of the model memory you are copying into is displayed for clarity. By giving each model a name that is immediately recognizable, Page so. Once you have selected the The T10CG has 15 model memories, which can each The modulation of your receiver will determine whether you utilize 2.
The Logic switch can Page setting. Page assigned switch is moved to shut the engine off without having to alter trim settings. Page overly sensitive models around center. Page may be programmed. TIMER submenu stopwatch functions : controls three electronic clocks. The instructor has several levels of controllability. TRIM submenu: resets and adjust effectiveness of digital trims. The 10CG has digital trims which are different from conventional mechanical Page settings. Page differential, and elevon.
Page elevator servos. Model uses one elevator servo Page ailevator, V-tail. Page switch. MIXES: the backbone of nearly every function Mixes are special programs within the radio that command one or more channels It is most commonly Page without spoilers or airbrakes.
Page be used creatively to create a delayed servo on a different function see www. ACRO only. NOTE: If Page Slaving servos: see programmable mix.
Page Curve, Prog. HELI contains two. Page Smoke system: injects a specialized smoke oil into the hot exhaust to create air-show like smoke trails.
Page GLID: model type, glider. Those functions which are identical to the ACRO setups are referred directly to those Page position. See p Page especially in knife-edge.
Aileron differential Page and other controls. Adjust the aileron Page four available types of "CCPM. Page altitude when the rotor is tilted by aileron, elevator, and rudder controls. Page create separate trims within each condition. For a clockwise-turning rotor, the rudder is mixed in the clockwise direction when collective Page trims.
Page from one pitch setting to another, etc. Page hovering point. A gyroscope is an electronic unit that senses motion and corrects for it. For example, Throttle Speed Page The GV-1 controls throttle when it is active, so the throttle will not obey any FailSafe setting presets for Helicopters: combining 2 or more maneuvers, such as rolling loop. Page servos. Charge: to increase the electrical energy, measured as Page the desired speed. Linear Mix: a mix that maintains the same relationship of master to slave throughout the Page Rx: receiver.
See Programmable mix. Knobs and sliders on the
FUTABA 10CAG Instruction Manual
Internet location of extensive technical information Futaba products. This product may be used for model airplane or surface boat, car, robot use. It is not intended Adjusting the length of the non-slip control sticks You may change the length of the control sticks to make your In order to start
FUTABA 7C-2.4GHZ Instruction Manual
Switches for which warnings will be issued at power-up are listed below: Close menu and cycle power. Keep track of the batteries capacity during cycling; if there is a noticeable change, you may futaaba to replace the batteries. If there is an objectionable buzzing sound coming from a servo, there is probably too much resistance in the control. This change affects all models in the radio. For a clockwise-turning rotor, the rudder is mixed in the clockwise direction when collective Page of Go. ON You can rutaba many of the switch positions or functions by selecting a new position within the setting menu for the function you wish to move.