DIXEL XR100C PDF

Access all Dixell manuals. Sets the low temperature or pressure alarm level. In this menu you will find Pr1, which contains any parameters that can be accessed without a security code. Parameters in the Visible Menu can now be accessed dkxel.

Author:Samuzilkree Gardabar
Country:Sudan
Language:English (Spanish)
Genre:Art
Published (Last):10 July 2012
Pages:373
PDF File Size:18.24 Mb
ePub File Size:18.86 Mb
ISBN:477-6-67733-662-2
Downloads:61163
Price:Free* [*Free Regsitration Required]
Uploader:Mejar



Normal display is resumed once the actual temperature drops below this point or the time set in this parameter has expired Sets the period of time following the termination of a defrost during which period nothing happens. Sets the maximum duration time of the defrost Sets the temperature sensed by the evaporator xrc, above which the count towards next defrost is suspended as set in parameter IdF Only functions if Smart Defrost is enabled see parameter EdF Sets the evaporator dixeel at which the controller will terminate the defrost.

It can also be used to stagger the re-start of multiple units following a power failure, to prevent everything trying to start at once and blowing a fuse. This gives a display resolution of either 1 degree or 0. Only for XRC with alarm relay: Sets the maximum temperature sensed by the evaporator probe above which the controller stops evaporator fans from running Sets the time delay between the end of defrost and the evaporator fans re-starting. Sensor interference and extension of probe cables It is important to avoid running probe cables close to power cables or other electrical equipment and cables that carry or switch heavy loads.

Click the X to close this notice. If set for hot gas, the compressor is kept running during defrost Sets the evaporator temperature at which the controller will terminate the defrost. Read only — for factory use. During the energy saving cycle, the temperature display will flash. Sets the low temperature or pressure alarm level. This is even more important when extending probe cables.

This can be used to prevent short cycling of the compressor following a momentary power failure, or to stagger the re-start of multiple units following a power failure, to prevent everything trying to start at once and blowing a fuse.

Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail. Sets the minimum time interval between the switching off and back on again of the same stage 0.

Adjusts the off — set of the evaporator probe Turns the decimal point on or off. The controller will then resume normal operation after this defrost terminates Sets the interval time between xxrc start of successive defrosts When a defrost is due rixel commence after the IdF timethis parameter adds a period of time during which the start of defrost is delayed.

You will also find Pr2, which contains all parameters but requires a security code to gain access. These industrial and commercial products play an important role in ensuring human comfort and protecting food throughout the cold chain. Have all the required parameters now been set correctly? For more specific information on how we use cookies and to change your cookie preferences, see our Cookie Notice.

XRC only Allows or prevents muting of the alarm buzzer and alarm relay. Good Practice should at all times be observed. Sets the current minute 0. Tells the controller whether to do an immediate defrost when the power is switched on or to wait for the normal interval time as set in parameter IdF. This input type must be specified at time of order. Turns the decimal point on or off. The controller will then resume normal operation Sets the interval time between the start of successive defrosts After defrost, the temperature as it was at commencement of defrost is displayed.

They can be used to control multiple stages, compressors, condenser fans, heaters or pumps. PTC temperature probe input models only. Sets the initial temperature alarm delay time on start up so avoiding unnecessary alarms during pull down.

All relays turn off. Pr2 0 0 to mins. Sets the number of degrees xr or below Set Point 2 at which the load is switched on. Sets the time delay between a temperature alarm condition being sensed and the alarm being signaled during normal operation.

The start time for each defrost is stored in non volatile memory, so these will not have been lost. Enables the controller to be re-calibrated or off-set from the probe temperature reading. However, the method diel programming any Dixell controller is very similar across all the range.

Sets the defrost mode. This tells the controller what to display during defrost. If no button is pressed for 15 seconds, the controller will revert to normal display. Innovation and efficiency for a better environment Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail.

Related Posts

ATANATIYA SUTTA PALI PDF

DIXEL XR100C PDF

Aranos To omit a particular defrost period, set it to Normal display dixe resumed once the actual temperature drops below this point or the time set in this parameter has expired Tells the controller whether to do an immediate defrost when the power is switched on or to wait for the normal interval time as set in parameter IdF. If linked, then when Set Point 1 is altered, Set Point 2 will follow it. Use them in conjunction with the parameter list for a duxel model Note: This tells the controller what to display during defrost. Tells the controller how many stages it is controlling.

BUKU STENSILAN PDF

Strona główna

.

Related Articles