Akira Other light curtain installation characteristics, such as a parallel approach, approach in angle and dual-position equipment shall meet the specific conditions provided in ISO Email Digite seu e-mail. Reaching over protective structure. Some of the standards generally required to apply to most machines are: The provisions of the abbt standards and annexes shall be observed, where applicable. Inspection at the final qbnt site.
|Published (Last):||3 January 2013|
|PDF File Size:||15.21 Mb|
|ePub File Size:||4.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
Vohn In addition to these nbrnm-uso, electric powered machinery must comply with IEC On hydraulic press brakes equipped with AOPD laser that uses a foot switch to actuate descending movement, it shall be of safe and have the following positions:. Conformity assessment approach NR 12 First the manuals and designs of the machine or equipment are compiled.
In addition, the section of 15 mm fifteen millimeters in thickness of the test gauge shall pass abnf the tools. Issuance of test reports. C Requirements for the use of optoelectronic laser presence detectors — AOPD in hydraulic nbrbm-iso brakes.
There shall be no interpolation of the values given in Table 2. The AGV must be designed to suit its purpose or nbdnm-iso, and can be adjusted and maintained without putting people at risk when used under the conditions envisaged by the manufacturer. This means that, in order to provide adequate safety for workers, it is not enough to meet the requirements of NR The light curtains shall be installed so that its detection area covers the access to the danger zone, with care taken not to provide spaces for the dead zone, i.
Additional requirements for automated functions on trucks. The opening of the tool can be activated, provided nbnrm-iso the risk of falling product in process is controlled, with actuation of foot switsch to the 3rd third position or releasing it to the 1st first position.
Inspection at the final installation site. The provisions of the specific standards and annexes shall be observed, where applicable. Safety — Sinova This annex establishes references to safety distances and requirements for the machines and equipments in general. Compilation of documentation and revision. Verify the detection capacity between the tool tip and the laser beam — the closest to the tool.
Conformity assessment services of machines and equipment in accordance with NR Get to know our conformity assessment services for machines and equipment according to the mandatory requirements. In respect to the detection capacity of the light curtain, at least an additional distance C in Table IV shall be used when calculating the minimum distance S.
The section of 10 mm ten millimeters in thickness of the test gauge placed on the matrix — the lower part of the tool — shall not be touched during the descending course of the tool. Testing system in hydraulic press brakes equipped with optoelectronic laser presence detector:. The tests shall be performed with a test gauge provided by the AOPD laser device manufacturer, which consists of a piece of plastic with sections of certain dimensions for this purpose, according to Figure 3.
Safety of Machinery and Equipment According to NR 12 Machines with a pneumatic system must comply with ISO and those with a hydraulic system must conform to ISO The 3rd third position can be actuated through a pressure point; the required force shall not exceed N three hundred and fifty Newtons.
Reaching over protective structure. To become compatible with Brazilian legislation on the safety of machinery and equipment. Benefits of our NR 12 compliance services With the help of our Ngrnm-iso 12 conformity assessment services for machines and equipment you will: We offer an independent inspection of machines and equipment with services that include design assessment, manufacturing and use, safety testing, functional testing, compliance with national and international standards and technical documentation.
The test shall be performed with a handle — cylindrical part with 14 mm fourteen millimeters of diameter of the test gauge, as shown in Figure 3. Most 10 Related.
NBRNM-ISO13852 de 05/2003
Fera Safety of Machinery and Equipment According to NR 12 In addition, the section of 15 mm fifteen millimeters in thickness of the test gauge shall pass between the tools. Inspection at the final installation site. Machines with a pneumatic system must comply with ISO and those with a hydraulic system must conform abmt ISO The light curtain application in hydraulic press brakes shall meet EN On hydraulic press brakes equipped with AOPD laser that uses a foot switch to actuate nbnm-iso movement, it shall be of safe and have the following positions:. Reaching over protective structure. The main objective of the standard is to ensure that safe machinery and equipment is inherently safe by requiring complete information on transport, use, maintenance and disposal.
NBR NM 13852.pdf
NM-ISO13852 DE 05/2003
ABNT NBRNM-ISO 13852 PDF