HP L1750 PDF

Warranty types Warranty removed from product: This product was designated to be returned to HP. Thus, the warranty has been removed from this product. Product sold by third party: This product was sold by a third party. Any warranty support needed would be completed by the third party that sold the product.

Author:Kagazuru Yozshurr
Language:English (Spanish)
Published (Last):3 March 2012
PDF File Size:3.51 Mb
ePub File Size:14.53 Mb
Price:Free* [*Free Regsitration Required]

Connects the AC power cord to the monitor. Cable Management Use the cable management feature to secure and hide your cables when viewed from the front. Before connecting the cables to monitor models with a single-hinged base, route the cables through the hole in the center of the monitor stand.

Figure : Using the Cable Management Feature Single-Hinged Base After connecting the cables to monitor models with a double-hinged base, place the cables through the cable management channels on the sides of the monitor base.

The video mode is determined by the video cable used. The monitor will automatically determine which inputs have valid video signals. For analog operation, use the VGA signal cable provided.

For digital operation, use the DVI-D signal cable provided select models. Figure : Connecting the Signal Cable Connect the built-in monitor speakers on select models to the computer using the audio cable. Figure : Connecting the USB Cable warning: To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug.

The grounding plug is an important safety feature. Plug the power cord into a grounded earthed electrical outlet that is easily accessible at all times. Disconnect power from the equipment by unplugging the power cord from the electrical outlet. For your safety, do not place anything on power cords or cables. Arrange them so that no one may accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by the plug.

Connect one end of the power cable to the AC power connector on the back of the monitor, and the other end to an electrical wall outlet. Figure : Connecting the Power Cable Adjusting the Monitor Your monitor model may look different than the model in the following illustrations. Figure : Tilting the Monitor Swivel the monitor to the left or right for the best viewing angle select models. Figure : Adjusting the Height Pivot the monitor clockwise from landscape to portrait orientation viewing to adapt to your application select models.

Figure : Pivoting the Monitor note: To view information on the screen in portrait mode, you will need to install the Pivot Pro software included on the software and documentation CD. The position of the OSD menu can also be rotated to portrait mode.

Turning on the Monitor Press the power button on the computer to turn it on. Press the power button on the front of the monitor to turn it on. Image retention is a condition that may occur on all LCD screens. To disable this feature, press and hold the monitor power button for 10 seconds.

Some models include two additional USB connectors on the side panel of the monitor. Refer to Step 4 in Connecting the Cables. Refer to the documentation included with the optional device for detailed mounting instructions. Figure : Using the Accessory Rails Feature Removing the Monitor Pedestal Base You can remove the monitor panel from the pedestal base to install the panel on a wall, a swing arm, or other mounting fixture.

If the monitor has a connected audio cable, disconnect it. Disconnect and remove the signal and power cables from the back of the monitor. Lay the monitor face down on a flat surface. Remove the screws on the back of the monitor that connect the monitor panel with the pedestal base. On the double-hinged base, there are four screws that connect the monitor panel to the pedestal base. Figure : Removing the Double-Hinged Pedestal Base On the single-hinged base, there are three screws that connect the monitor panel to the pedestal base.

Figure : Removing the Single-Hinged Pedestal Base Lift up on the pedestal base to remove it from the monitor display head. Mounting the Monitor HP provides an HP Flat Panel Monitor Quick Release purchased separately that installs to the back of the monitor panel and allows you to quickly and securely attach the panel to a wall or swing arm mounting fixture.

Refer to Removing the Monitor Pedestal Base steps in the previous section. To attach a third-party mounting solution to the monitor, four 4 mm, 0. Longer screws should not be used because they may damage the monitor. For best performance, it is important to use the power and video cables provided with the monitor.

Set the monitor panel down on a flat, soft, protected surface. Place the optional HP Quick Release onto the back of the monitor. Line up the holes on the HP Quick Release with the mounting holes on the back of the monitor. Mount the HP Quick Release to a swing arm or other mounting fixture using the four screws removed from the back of the monitor in the previous step. If you are mounting to a wall, HP recommends that you consult with a qualified engineering, architectural, or construction professional to determine the appropriate type and quantity of mounting fasteners required for your application and to ensure that the mounting solution is properly installed to support applied loads.

Insert the monitor panel into the HP Quick Release, and then press down firmly on the monitor to lock it in place. When the HP Quick Release locks, it will make a clicking sound. Locating the Rating Labels The rating labels on the monitor provide the spare part number, product number, and serial number. You may need these numbers when contacting HP about the monitor model.

The rating labels are located on the rear panel of the monitor display head.


HP L1750 Specs



17-inch LCD Monitor Specifications - L1750 Model


Related Articles